3DXTech 3DXSTAT ESD Safe PEKK-A 1.75mm 500gms

3DXTech 3DXSTAT ESD Safe PEKK-A 1.75mm 500gms

£350.93 £292.44 ex. VAT

In stock

£350.93 £292.44 ex. VAT

ESD PEKK is an Ultra Performance filament, ideal for demanding applications in Aerospace, Defense, Automotive, and Electronics applications.

Availability: In stock SKU: 32117


3DXSTAT ESD PEKK-A – Ultra Performance 3D Printing Material

Made using Arkema Kepstan PEKK (PolyEtherKetoneKetone) and state of the art conductive additives, this ESD-safe PEKK is one of the highest-performance polymers in the world.  ESD PEKK is ideal for demanding applications in aerospace, defense, automotive, and electronics applications.

Aerospace-Grade Performance. This filament was created for the most demanding applications where tightly controlled static dissipation, thermal properties, mechanical performance, low outgassing, and chemical resistance properties are required.

3DXSTAT ESD PEKK-A product attributes include:

  • Made using the 60/40 type PEKK copolymer (PEKK-A)
  • Substantially easier to print than PEEK
  • Glass Transition Temp (Tg) of 162°C (20°C higher than PEEK)
  • Heat distortion temperature (HDT) of 150°C
  • Melt Temp (Tm) of 305°C (allows for lower print temps than PEEK)
  • 10^4 to 10^9ohm surface resistivity on 3DP sample using concentric ring test method
  • Consistent surface resistivity and low particulate contamination
  • Low outgassing – ideal for space related applications
  • PEKK has inherent flame resistance
  • Long-term hydrolytic stability in steam and autoclave environments
  • Excellent dimensional stability (low creep and low/uniform coefficient of thermal expansion) allowing for highly reproducible part-to-part dimensions
  • Exceptional strength and modulus, even at elevated temperatures
  • Excellent resistance to a broad range of chemicals, such as automotive fluids, fully halogenated hydrocarbons, alcohols, and aqueous solutions
  • Stable dielectric constant and dissipation factor over a wide range of temperatures and frequencies

3DXSTAT ESD PEKK-A compared to Stratasys? Antero PEKK 840CN03:

  • 3DXTECH and Stratasys both use PEKK-A from Arkema as the base resin
  • 3DXTECH and Stratasys both use carbon nanotubes as the conductive additive
  • 3DXTSTAT ESD PEKK-A is lower cost and suitable for use on many lower cost open-source 3D printers, including the Gearbox HT2.
  • Stratasys Antero 840CN03 is more expensive and only available on the ultra-expensive Fortus 900mc Plus

Filament Specifications:

  • Diameter: 1.75mm (+/- 0.05mm)
  • Larger reels and custom diameters available upon request

Surface conductivity as a function of extruder temperature:

The surface resistance of the printed ESD-safe part will vary depending on the printer’s extruder temperature. For example, if your testing indicates the part is too insulative, then increasing the extruder temperature will result in improved conductivity. Therefore, the surface resistance can be ‘dialed-in’ by adjusting the extruder temperature up or down depending on the reading you receive on your part.

Recommended Print Conditions:

  • Extruder Temp: 355 – 385°C
  • Bed Temp: 120 – 140°C
  • Bed Prep: Ultem Tape is the ideal build surface, glue stick on clean glass is suitable
  • Enclosure temp (if your printer is equipped): 70 – 140°C
  • Drying Instructions: Please see the following instructions for when you want to dry out this filament, HERE.

Fortus and Antero are trademarks of Stratasys LTD and not affiliated with 3DXTECH LLC.
Kepstan is a registered trademark of Arkema






A premier polymer – one of the highest performance thermoplastics ever invented.

PEEK is an ultra-performance filament, ideal for the most demanding functions in Aerospace, Automotive and Electronic applications. This is possible as it has incredible mechanical properties, excellent strength and durability, resistance to corrosion and temperatures, and flame retardancy. It can withstand boiling water and steam.

Printing with this material is very difficult and requires a significant amount of experience in 3D printing. A high quality or heavily modified printer is mandatory. 



Very High


Very High


Very Difficult



Recommended Settings

Print Temp

375°C -410°C

Temp may vary on brand

Bed Temp

165°C – 175°C

Temp may vary on brand

Print Surface

Heated Bed Required
Enclosure Required
Hardened Steel Nozzle reccomended

Example Prints

Additional information

Weight0.5 kg
Dimensions210 × 210 × 75 mm
Filament Brand


Filament Colour


Filament Diameter


Filament Spool


Filament Type


Filament Weight


Filament Range

3DXTech 3DXStat


There are no reviews yet.

Be the first to review “3DXTech 3DXSTAT ESD Safe PEKK-A 1.75mm 500gms”