Dragon Scale Purple HTPLA 1.75mm 500gms 3D printing filament

Dragon Scale Purple HTPLA 1.75mm 500gms 3D printing filament

£32.00 £38.40 inc. VAT £28.80 £34.56 inc. VAT

In stock

£32.00 £38.40 inc. VAT £28.80 £34.56 inc. VAT

Availability: In stock SKU: 640970864358

Description

A purple that pops!

@protopasta Don’t melt in the heat! Dragon Scale Purple #3dprinting #filament #Popsicle #3dprint #design ♬ original sound – Protopasta

  • A bright, frosty purple with plenty of silver pearl for texture and pop.
  • A beautiful, lighter-in-color alternative to Galactic Empire Metallic Purple.
  • Designed in collaboration with Luke Goodman (Out of Darts) & produced by Protoplant, makers of Protopasta

Created from our highest quality HTPLA, if there is one purple to print with, this is it! Print with the ease of standard PLA with standard hardware and temperatures, but make fun, mesmerizing prints that stand out.  Celebrate good times by printing toys, treasures, and keepsakes.  If you want to make a print more fun, just add some metallic pop!  Our metallic finish contains no actual metal and has little risk of clogging or wearing your nozzle, and it won’t make a glitter mess, but beware the printing is sure to be addictive!

Metallic particles are relatively small but have some orientation effects, giving top/bottom surfaces more shine than sidewall, so have some fun playing with orientation to see how the result changes!  We recommend 0.2 mm layers for the best result. Like our other HTPLAs, Metallic HTPLA can be “Heat Treated”  to increase crystallinity for “Higher Temperature” resistance compared to amorphous PLA, ABS, and co-polyesters like PETG!  Glittler Flake HTPLA prints translucence, but turns opaque when heat treated (or crystallized).  With a more crystalline structure, heat treated HTPLA parts can hold form to near melting, though temperatures where the material is practically useful vary greatly depending on geometry and load conditions! For this improved the performance, your prints should be baked in an oven until you see a change from translucent to opaque with reduced gloss.  This visual change indicating the improved performance! We’ve  seen the change take place in 5-10 minutes on thin walled parts but can take an hour or more.  We’ve had good luck in a quality, at home convection oven at 110C (225F).  Parts will get very “floppy” before becoming more firm, so please leave supports on your parts or support them and bake them on a flat, non-radiating surface (like glass, ceramic, or composite).

  • Available in 1.75 & 2.85 (3) mm diameter on a 500g diameter recyclable cardboard spool
  • Usable on most PLA-compatible printers, such as Lulzbot, Makerbot, FlashForge, Dremel, Ultimaker, Printrbot, and more!

No abrasive fillers so expect normal wear with standard nozzles.

In our experience, good results were achieved using standard PLA parameters ranging from 195-225C nozzle with standard build surface preparation (blue tape, glue stick, Lokbuild or PrintBite). No heated bed required but up to 60C is okay.  Beware, if the bed temperature is too high, your part base could actually heat treat while printing, increasing warping and decreasing adhesion.  Some shrinkage will occur in the heat treating process, so dimension critical parts may need to be scaled appropriately (as much as 2.5% in our experience).

PLA

Overview

PLA is easy to print, at low cost. Non-toxic and Eco friendly. A perfect starting point for people new to 3D printing.

PLA is created from all-natural renewable resources, and under the correct conditions, is fully biodegradable. This material is typically used for prototypes or decorative prints; Due to the low temperatures and ease of use, features tend to print sharper and more detailed. Its non-toxic nature means that it can be printed for food and medical applications if done so from a sterile and sanitized environment. 
However, PLA prints are prone to snapping and breaking under pressure, and become damaged and discolored from high temperatures and prolonged exposure to sunlight or water. 

Used for: Design prototypes, Plastic Cups, Medical Implants, Food containers.

Strength

Medium

Durability

Low

Printability

Very Easy

Pros

Cons

Recommended Settings

Print Temp

180°C -210°C

Cooling Fan on

Temp may vary on brand

Bed Temp

0°C – 45°C

Temp may vary on brand

Print Surface

No Heated Bed Required
No Enclosure Required

Example Prints

Additional information

Weight0.5 kg
Dimensions200 × 200 × 55 mm
Filament Brand

proto-pasta

Filament Colour

Multicolour, Purple

Filament Diameter

1.75mm

Filament Type

PLA

Filament Weight

500gms

Filament Weight

500gms

Filament Range

Proto-pasta HTPLA

Filament Properties

High Strength

1 review for Dragon Scale Purple HTPLA 1.75mm 500gms 3D printing filament

  1. 5 out of 5

    Colin Durrans

    Awesome Colour, Slight metalic scheen

    I’d a sample of this, great colour. This was run with my usual PLA settings, it appears the retract should be just a little higher but it was soo close. Really easy printing, great finish.


Add a review